SabreW's GFX Amateur Hour
After some practice, I've come up with some new GFX stuff to show you guys. Some of these are some old things that I've touched up with new techniques and whatnot, while others are brand new. Lemme know what you guys think of them. These are just

Amateur (Ham) Radio
Come And Join Us on the Airwaves

coltendude's Avatar and Signature Amateur Shop
Hey everyone! Like the title says, this is my avatar and signature shop! Starting Prices (These prices may go up depending on how much the demand for Avs/Sigs increases) -Avatar (120 x 120) = 5DP -Signature (500 x 200) = 10DP Requesting

Sound Valves VTP101i / Pas3 II clone kit?
Does anyone make a preamp kit that is a single ended, class A, cathode follower circuit with regulated heater and B+ power supplies using low noise rectifiers and has a cathode follower phono stage? Tone controls would be nice too. I would like to find

Pinch valves
I just thought I would start this topic off because it is always coming up (A perennial I think!) (I will post my take on the topic very soon.)

Replacment Valves for BLACK STAR SERIES ONE 100 HEAD
I have just bought a Blackstar Series 1 100 head and I quite new to tube amps. I was wondering if I could buy a valve set (all 8 valves) that I can use to replace the valves when needed.. Do you know what valve make do I need to purchase to keep it as

6L6 Valves
Has anyone put 6L6 valves in a blackstar ht100? and ive not would it blow the amp if you did thanks tom

Needle valves?
Does anyone know where I might get replacement needles for these backplates? A needle from a SureStart fits the black one, but doesn't work properly, engine runs rich, and any attempt to lean it out makes it cut. The red backplate has a smaller

my own silly, amateur-ish 'art'? *ahem* :-)
Hello fine peoples of the GSG World! I posted a little stuff on me personal gallery.... I'm one of those folks who can't draw to save his life but doesn't let that stop'm from posting his 'art' anyways! lolz I know it stinks, but I'm hopin' you'll

Regulator and Safety Valves
HI STW Since the latest kit tells us to install the safety valves. I been thinking. Would it be wiser to hold off until the regulator handle assembly arrives as currently the regulator block is not adjusted to the correct length in the cylinder.

HT 20 preamp valves change
Hello, I'm considering to change the 2 preamp valve on my HT-20 head (through an open back V30), searching for little more gain and bite. Has someone tried to do it? Some advices? Is it worth to change the stock TADs? Thank you, Luigi

Ace's HG&SS Icons/Commemorative Prints/ Amateur Card Maker/ Amateur Trainer Sprite Maker
Icons Mine Lindsay Jack, The Australian one Quan Blitzer Rocket Grunt with bluish/purple hair, Red Eyes, and followed by Umbreon Naruto's (Forgot about the Blue Eyes hehe sorry, will fix that later) David's (Fix the hat

Amateur Blackwings
Monsters:20 Gale x1 Shura the Blue Flame x3 Bora the Spear x3 Sirroco the Dawn x3 Vayu the Emblem of honor x2 Kalut the moon shadow x1 Elphin the Raven x1 Breeze the Zephyr x1 Mistral the silver Shield x2 Blizzard the Far North x2 Dark Armed

Amateur Blackwings
Monsters:20 Gale x1 Shura the Blue Flame x3 Bora the Spear x3 Sirroco the Dawn x3 Vayu the Emblem of honor x2 Kalut the moon shadow x1 Elphin the Raven x1 Breeze the Zephyr x1 Mistral the silver Shield x2 Blizzard the Far North x2 Dark Armed

4" Burrell Ramsbottom safety valves
I have a near completed LSM design 6NHP 4" Burrel agricultural engine. I am struggling to a point of extreme frustration trying to get a successful workng safety valve. I used the LSM design but I could never get a decent valve seating such that it